آموزش نحوه ساخت مدار فرستنده fm ساده

[Dplay]

آموزش نحوه ساخت مدار فرستنده FM ساده




توضیحات:
- این مدار در فضای آزاد تا 300 متر برد دارد.
- فرکانس اسیلاتور آن حدود 100 مگاهرتز است.
- ترانزیستور اول کار تقویت سیگنال ورودی میکروفن را انجام می دهد.
- اسیلاتور این مدار از نوع کولپیتس است.
- برای دریافت امواج ارسال شده توسط این مدار باید موج رایوی را روی فرکانس 89-90 مگاهرتز تنظیم کرد.
- برای تنظیم خازن متغیر بهتر است از پیچ گوشتی پلاستیکی استفاده شود تا نویز حداقل شود .


اطلاعات بیشتر در ادامه مطلب

Description

This FM transmitter (FM Tx) is about the simplest and most basic FM Tx it is possible to build and have a useful
transmitting range. It is surprisingly powerful despite its small component count and 3V operating voltage. It will
easily penetrate over three floors of an apartment building and go over 300 meters in the open air. The circuit
we use is based on a proven Australian design. It may be tuned anywhere in the FM band. Or it may be tuned
outside the commercial M band for greater privacy. (Of course this means you must modify your FM radio to
be able to receive the transmission or have a broad-band FM receiver.) The output power of this FM Tx is below
the legal limits of many countries (eg, USA and Australia). However, some countries may ban ALL wireless transmissions without a license. It is the responsibility of the builder to check the legal requirements for the operation of this circuit and to obey them.

CIRCUIT DESCRIPTION:

The circuit is basically a radio frequency (RF) oscillator that operates around 100 MHz. Audio picked up and
amplified by the electret microphone is fed into the audio amplifier stage built around the first transistor. Output
from the collector is fed into the base of the second transistor where it modulates the resonant frequency of
the tank circuit (the 5 turn coil and the trimcap) by varying the junction capacitance of the transistor. Junction
capacitance is a function of the potential difference applied to the base of the transistor. The tank circuit is
connected in a Colpitts oscillator circuit.

CIRCUIT CALIBRATION:

Place the transmitter about 10 feet from a FM radio. Set the radio to somewhere about 89 - 90 MHz. Walk back to
the Fm Tx and turn it on. Spread the winding of the coil apart by approximately 1mm from each other. No coil winding should be touching another winding. Use a small screw driver to tune the trim cap. Remove the screwdriver from the trim screw after every adjustment so the LC circuit is not affected by stray capacitance. Or use a plastic screwdriver. If you have difficulty finding the transmitting frequency then have a second person tune up and down the FM dial after every adjustment. One full turn of the trim cap will cover its full range of capacitance from 6pF to 45pF. The normal FM band tunes in over about one tenth of the full range of the tuning cap. So it is best to adjust it in steps of 5 to 10 degrees at each turn. So tuning takes a little patience but is not difficult. The reason that there must be at least 10 ft. separation between the radio and the Tx is that the Tx emits harmonics; it does not only emit on one frequency but on several different frequencies close to each other.

NOTE:
You may experiment with using 6V or 9V with the circuit to see how this increases the range of the transmitter. The sensitivity may be increased by lowering the 22K resistor to 10K. Try it and see